GENERATOR ENGINE EMISSIONS & TIER RATINGS EXPLAINED

DIESEL GENERATOR ENGINE EMISSIONS & TIER RATINGS EXPLAINED

WPP’s comprehensive inventory of new and used generators, covering all tier levels, is unequaled in the industry. Since the 1950s, the US government has been making plans to combat air pollution. From its inception to enforce the Clean Air Act of 1970, a law which provided much more stringent emission regulations, the Environmental Protection Agency (EPA) has implemented regulations strategically to improve air quality by reducing harmful emissions. Diesel exhaust is one of these harmful emissions, and as such, the regulations have had an impact on on-road and off-road vehicles and engines, including non-road diesel engines and stationary diesel engine generator sets (find out if diesel generators really are bad for the environment). But though this may sound as though it were a hardship for this industry, it has led to engine improvements that reduce emissions and boost performance. To make the process go smoothly, an implementation system was designed to allow all stakeholders—including scientists and manufacturers, among others—to develop the knowledge and technologies necessary to meet these regulatory goals. Really, the implementation system is more accurately described as a tier system put in place to accommodate the process. Here, we outline what you should know about the tier emissions ratings for diesel generators.

What Are Tier Levels?

There are four tiers in place to reduce harmful gases into the atmosphere, and each tier was built off the other to make compliance more manageable. Each tier level also has a certain standard with regard to harmful emissions and provides a cap at which point emissions must be limited. The standard progresses over the years in accordance with the tier level.

The intended and primary emissions to be reduced include:

  • Nitrogen oxides (NOx)
  • Hydrocarbons (HC)
  • Carbon monoxide (CO)
  • Particulate matter (PM)
  • Non-methane hydrocarbons (NMHC)

Currently, all engines (with a few exceptions–discussed later) are at the Tier 4 Final level, meaning the engines are designed to emit reduced harmful emissions using diesel oxidation catalysts (DOCs), diesel particulate filters (DPFs), and selective catalytic reduction (SCR) systems. Engine emissions are still a work in progress, especially for diesel engines, both on and off the road.

How Often Does A Generator Need Testing?
The frequency schedule for load bank testing on a generator often depends on how the generator is classified and what it is a standby for. For example, if a generator is used as a backup for services associated with loss of life or serious injury—such as in a hospital setting—the testing guidelines per safety codes are much more frequent. Data centers and financial organizations are generally held to stricter requirements, as well. These standard guidelines are set by the National Fire Protection Association (NFPA). Critical situations follow NFPA 110 & 99 and lesser situations follow NFPA 70.

In most cases, it is recommended that non-mission critical generators are tested at 80% of their maximum load for 60 minutes at least once per year. Critical diesel generators could be tested much more frequently, but this wholly depends on individual requirements and industry regulations. If this monthly test fails, load bank testing for a minimum of two consecutive hours is recommended. Companies can either hire a load bank for when the generator needs testing or have one permanently on-site. It largely depends on the needs of each company. A business that operates several generators is typically more suited to having its own load bank permanently stationed on-site, but the best solution is not always clear-cut.

How Do Tier Levels Relate To Generators?
Diesel engines were not the initial target when the EPA regulations were first published and implemented. But they are very much the subject of these regulations now. In 1998, non-road engine regulations were put into place as a 3-tiered system (with the 4th tier later added). Each tier involves a phase-in period over a number of years and in accordance with the engine’s horsepower rating. Below is an overview of these three tiers and how they relate to generators.

Tier 1 & Diesel Generator Emissions
Though Tier 1 standards were published in 1991, the implementation for diesel engines and generators did not begin until 1996 with the intention that all diesel engines and generators be in compliance by 2005. Initially, Tier 1 standards focused on diesel equipment under 37 kW (50 hp) with the phase-in period from 1996 to 2000. The below table identifies Tier 1 standards related to diesel engine power and harmful gases to be limited.

Tiers 2 & 3 Diesel Generator Emissions
Tier 2 standards were published in 1999 and Tier 3 standards were published shortly thereafter. These phases, however, did not begin until 2001 with all engines to be in compliance by 2008. These two levels required engines that were more sophisticated in design and advanced in performance in order to meet the criteria set out in the regulations. The below table identifies Tier 2 and 3 standards related to diesel engine power and harmful gases to be limited.

To note, sulfur content was not originally limited by environmental regulations in Tier 1 for non-road diesel fuels but was later mandated and required to be met by 2007 in Tiers 2 and 3.

Tier 4 – The Current Emissions Standard For Diesel Generators
Tier 4 is in effect today, so all new prime power and portable diesel generators should be manufactured to meet this tier requirement. Tier 4 is, of course, the strictest of all previous regulations and requires the most advanced technologies to achieve the greatest reduction in emissions available today: near-zero emission levels.

Tier 4 emission standards began being phased-in in 2008. The regulations set out to reduce NOx, particulate matter, and hydrocarbon emissions substantially with respect to all off-road and on-road engines and generator sets. Carbon monoxide standards, however, remain relatively similar to those established in Tiers 2 and 3.

How Do Diesel Engine Companies Meet The Standards Established By The EPA Emission Tier System?
Manufacturers, designers, and other relevant companies must improve the technologies and design of diesel generators so that they are in compliance with the law. Examples of what companies are doing to be in compliance materialize in a number of ways, including:

Engine Design Technologies

  • Fuel injection technology to improve injection timing to limit NOx emissions and injection pressure to limit PM emissions.
  • Exhaust gas recirculation to control NOx emissions.
  • Intake boosting for efficiency and PM reduction.
  • Intake temperature management technology to limit NOx and PM emissions.
  • Combustion chamber designs to measure and control PM emissions.

Fuel & Lubricant Technologies

  • Lubricating oil to reduce fuel consumption overall.
  • Alternative fuels to reduce carbon dioxide emissions.

Exhaust Add-ons and Aftertreatment Technologies

  • Selective Catalytic Reduction (SCR) to reduce NOx up to 50% in active systems.
  • Diesel Particulate Filter (DPF) to reduce emissions more than 90%.
  • Exhaust Gas Recirculation (EGR) to reduce emissions overall.
  • Diesel oxidation catalyst (DOC) to reduce high levels of HC and CO and moderate levels of PM as well as to enhance performance of SCR and DPF systems.

Emergency Vs Non-Emergency Generator Standards
The emission standards for emergency generators differ from the standards of non-emergency generators. This is important to know for those companies who have on-site or may need emergency standby generators. The difference is founded on the basic reality that emergency generators are used for a temporary purposes and therefore not subject to the more stringent rules. Here’s what you should know.

As noted above, only prime generators need to adhere to Tier 4 standards. Standby (or emergency) gensets are only subject to Tiers 2 and 3, not Tier 4. As such, these machines used as standby only machines do not need to be updated if in compliance with Tier 2 or 3 standards. All our generators, whether for purchase or rental, meet the emission tier standards for their role.

Benefits Of Tier 4 Generators
We noted at the beginning that though the tier-system seems to burden manufacturers and users of diesel engines and generators, it does offer benefits, too. Some of these benefits include:

  • Significant emission reduction.
  • Quieter and smoother operation.
  • Increased fuel efficiency.
    Advanced technologies for overall optimized performance.
  • Minimal downtime for extended service and reduction in costs.

Overall, your Tier 4 generator benefits you from all angles: health, expenses, performance, efficiency, and productivity.

What Comes After Tier 4?
Now that we are at Tier 4, what’s next? Tier 5 is the natural response, but the EPA has done little to move towards it. That said, most generator manufacturers do not operate or market to the United States alone: Europe is well on its way to phasing in regulations that could be considered as Tier 5 standards. Stage 5 in Europe, however, is comparable to its Stage 4 standard, so big changes are not anticipated; all to be expected is that companies keep moving forward with emission reductions and efficient productivity made possible through newer and more advanced technologies.

Because of the similarities between Stages 4 and 5 in Europe, manufacturers do not have to worry about compliance so long as in compliance with Tier 4. And we at Worldwide Power Products are in compliance and intend to keep moving forward — always keeping our eyes on the future, today.

Cr. https://www.wpowerproducts.com/news/generator-tier-ratings/